Sorque home

Equipment guide

Industrial valves: types, common problems, and how to choose

Industrial valves start, stop, throttle and divert flow, and they protect equipment from backflow and overpressure. According to the U.S. EPA’s leak detection and repair guide, valves outnumber every other kind of process equipment except connectors such as flanges, and earlier EPA studies found them to be the largest single source of emissions from leaking equipment.

This guide covers the main types of valves and their uses, common problems and fixes, maintenance, and how to choose a valve. Pressure relief valves get a short entry only, because their setting, testing and repair belong with qualified, authorized personnel.

Below the guide, Sorque users post peer reviews rating specific valves on effectiveness, reliability, maintenance, efficiency and downtime. The next section is a web summary of what practitioners say elsewhere, not a peer review.

Updated · Written for engineers, mechanics, and technicians

Web summary · not a peer review

What people are saying elsewhere

Forum threads and trade articles keep returning to one point: many valve failures are application problems, such as isolation valves run partly open, oversized control valves, or fluids harsher than the design assumed. Seized gate valves and packing leaks are the everyday complaints, and engineers repeat that a closed valve alone is not positive isolation.

  • Isolation valves are not throttling valves. Contributors to a thread on repeated gate valve failures named throttling at high velocity as a likely cause. The DOE handbook explains why: a partly open gate vibrates and wears its disk and seat.[1, 11]
  • Rarely used gate valves seize. Plumbing and heating technicians advise rocking a stuck handwheel gently rather than forcing it, since stems and gates break, and often replacing old gate valves with ball valves.[13]
  • Packing leaks: adjust first, then repack. Practitioners suggest tightening the packing nut first and favor graphite for repacking, warning that PTFE extrudes past the gland. The EPA identifies the stem and gland as the usual leak points on valves.[2, 14]
  • Find the root cause before buying a heavier valve. Faced with gates separating from stems, forum engineers pointed to water hammer, corrosion, sand, velocity and build quality, and asked for a teardown. Some favored a higher pressure class; others said a higher rating does not make the internals sturdier.[11]
  • Valve or tuning? Test before retuning. A panel of control experts said a steady cycle that shrinks as controller gain rises points to stiction or backlash, which retuning does little to fix. They listed linkage, tubing, air filters and packing friction as things to check.[15, 16]
  • Closed is not isolated. Engineers note that a shut valve does not give positive isolation for hot work or opening equipment; that takes a spade or blind. OSHA’s lockout standard treats line valves as energy-isolating devices that must be locked out and verified.[4, 12]

Summarized in our own words from the forum discussions and articles listed under Sources. These are other people’s reports, not Sorque peer reviews, and they never count toward ratings.

Types of industrial valves and their uses

Valves are grouped by how the closing element moves. Linear-motion valves (gate, globe, diaphragm, pinch) push a closure into the flow, quarter-turn valves (ball, butterfly, plug) rotate 90 degrees, and check and relief valves are worked by the process itself. Choose by the job first: isolation, throttling, backflow prevention or overpressure protection.

Gate valves

A wedge or parallel gate is raised or lowered across the flow by a threaded stem. Fully open, it leaves an almost clear bore with very low pressure drop.

Best for
On/off isolation in clean liquid, steam and gas lines.
Watch out for
Not for throttling: a partly open gate vibrates and wears its seat. Operation takes many turns, and a solid wedge closed hot can bind as it cools.

Globe and needle valves

A disk or plug moves straight onto a seat ring while the flow turns through the body. Needle valves are a small-bore version for fine metering.

Best for
Throttling, frequent operation and low seat leakage. Needle valves suit instrument and sample lines.
Watch out for
High pressure drop even fully open. Large high-pressure globe valves are heavy and need high operating force.

Ball valves

A bored ball turns a quarter turn against soft or metal seats. A floating ball seals on the downstream seat under line pressure. A trunnion-mounted ball sits on fixed shafts, which suits larger sizes and pressures.

Best for
Fast, tight, low-torque isolation in gas, hydrocarbon, chemical and utility service. V-port and segmented balls are built for control.
Watch out for
Standard ball valves throttle poorly because the partly exposed seat erodes. Soft seats have temperature limits, and fast closure can cause pressure surges in liquid lines.

Butterfly valves

A disk about the size of the bore turns a quarter turn. Concentric designs seal on a liner. Offset designs swing the disk off the seat as it opens, and triple-offset valves allow metal seats.

Best for
Large water, air, gas and slurry lines at modest pressure, and coarse throttling.
Watch out for
The disk stays in the flow, adding pressure drop and blocking pigging. Rangeability is limited, and high pressure recovery raises cavitation risk in liquid service.

Plug valves

A ported plug turns a quarter turn. Lubricated designs have sealant injected around the plug; sleeved and eccentric designs need none.

Best for
Gas, wastewater, slurries and multi-port diverting duty.
Watch out for
Metal plugs can gall. Lubricated plugs stick and leak without regular injection of a compatible sealant, and some multi-port layouts cannot shut off fully.

Check valves

Forward flow opens the disk; reverse flow, gravity or a spring closes it. Styles include swing, lift, tilting-disk, piston, dual-plate and nozzle checks.

Best for
Backflow prevention at pump and compressor discharges.
Watch out for
Slam when the disk closes late, chatter when flow cannot hold it fully open, and hinge wear. Swing checks do not suit pulsating flow.

Diaphragm and pinch valves

A flexible diaphragm, or a rubber sleeve in a pinch valve, is pressed closed, so the stem and bonnet never touch the fluid.

Best for
Corrosive chemicals, abrasive or fibrous slurries and hygienic service. Weir-type diaphragm valves can throttle over a limited range.
Watch out for
The diaphragm or sleeve is a wear part that sets the pressure and temperature limits and must suit the chemical. Exposed-sleeve pinch valves can collapse under vacuum.

Control valves

An actuator, usually with a positioner, moves the trim of a globe, ball, butterfly or eccentric plug body in response to a controller signal. The trim shape sets the flow characteristic, such as linear or equal percentage.

Best for
Continuous control of flow, pressure, level or temperature. Globe bodies generally give the most precise control.
Watch out for
Oversizing, packing friction, poor instrument air and aggressive tuning commonly cause poor control. The fail position (open, closed or last) must match the process hazard.

Pressure relief and safety valves

Spring-loaded or pilot-operated valves open automatically at a set pressure. A relief valve opens progressively and suits liquids. A safety valve pops fully open, reseats after pressure falls by its blowdown margin, and suits steam and gas.

Best for
Last-line overpressure protection for vessels, boilers and piping.
Watch out for
Sizing, setting, testing and repair fall under the ASME Boiler and Pressure Vessel Code and the National Board Inspection Code. Repairs go to authorized organizations such as National Board VR certificate holders. The EPA notes that these valves can leak if run too close to set pressure.

Common valve problems and how to fix them

Most valve trouble shows up as one of five symptoms: leakage to atmosphere, leakage through a closed valve, poor control, noise, or a valve that will not move. Any work that opens the pressure boundary needs the valve isolated, depressurized and verified under your site’s lockout and permit procedures.

Stem packing leaks

Symptoms
Weeping at the gland, vapor at the stem, stains or crystals around the packing nut, or hits in a leak survey.
Likely causes
Packing loses compression as the stem cycles, or dirt and corrosion score the stem. According to the EPA, the stem and gland are where valves most often leak, typically from failed packing or O-rings.
What to do
Tighten the gland nuts evenly in small steps, just enough to stop the leak. Chemical Processing links overtight packing to the sawtooth movement of a sticking control valve. Never back off gland nuts on a pressurized valve. If adjustment fails, isolate the valve and repack it with a material rated for the service. The EPA guide says LDAR rules usually require a first repair attempt within 5 days and a final one within 15. Chronic leakers may need packing type-tested to API 622, or a bellows-sealed valve.
Sources
2, 5, 14

Seat leakage (passing valves)

Symptoms
Flow, pressure or heat downstream of a closed valve, or a drain that keeps running after isolation.
Likely causes
Seats eroded by debris or by throttling, trapped solids, heat-damaged soft seats, corrosion, or an actuator that falls short of full travel.
What to do
Confirm the leak with a downstream pressure, temperature or ultrasonic check, then stroke the valve fully and check limit stops. Lap or replace the seats or the valve, and move throttling duty to a valve built for it. Specify a seat leakage class: ANSI/FCI 70-2 runs up to Class VI, the tightest, and Chemical Processing notes that safety-critical duties may need Class V or VI. Where one valve is not enough, use double block and bleed or a blind.
Sources
1, 5, 10, 11, 12

Control valve hunting and stiction

Symptoms
The loop cycles at steady load. A sticking valve gives a triangle or sawtooth controller output and a stepped process variable, while a loop tuned too hard cycles in smooth waves.
Likely causes
Tight packing, an oversized valve working near its seat, loose linkage, a misconfigured positioner, wet or dirty instrument air, or aggressive tuning.
What to do
Put the controller in manual. If the cycling stops, the cause is inside the loop. Then make small output steps in both directions. A valve that lags, jumps or fails to return to the same point has a mechanical fault that retuning will not fix. Chemical Processing cites ANSI/ISA-7.0.01 for an instrument air dew point at least 18°F below the lowest ambient temperature. Valve Magazine recommends sizing for about 60 to 80 percent open at maximum flow and, where possible, no less than about 20 percent open at minimum flow.
Sources
5, 6, 15, 16

Cavitation and flashing damage

Symptoms
Gravel-like noise, vibration, rough pitted trim (cavitation) or smooth, polished-looking erosion (flashing), and lost capacity or shutoff.
Likely causes
Pressure at the narrowest point of the flow falls below the liquid’s vapor pressure. Cavitation bubbles collapse violently as pressure recovers; in flashing, the vapor remains. Large pressure drops, hot liquids and high-recovery ball, butterfly and plug valves are most at risk.
What to do
Screen for cavitation at the sizing stage, for example with the ISA RP75.23 index. Reduce the pressure drop, move the valve to a higher-pressure point, or stage the drop with multistage trim, and use hard trim materials. Processing Magazine warns that an added orifice plate may only move the cavitation downstream. For flashing, flow-down angle bodies let the vapor form after the trim.
Sources
7, 8

Check valve slam and chatter

Symptoms
A bang and pressure spike when a pump stops, or tapping, hinge wear and broken disks in normal running.
Likely causes
Slam occurs when the disk is still open as the flow reverses, then shuts and stops the reverse flow abruptly. It is worst where flow decelerates quickly after a pump trip, as in high-head systems or parallel pumps. Chatter comes from a check valve too large for the flow, or from pulsating flow.
What to do
Match the closing behavior to the system: a check that closes very fast, such as a spring-assisted design, or one slowed by an oil dashpot. Size check valves for the flow, not the pipe, and fix the cause of surges rather than just buying a heavier valve.
Sources
1, 9, 11

Stuck, seized or broken valves

Symptoms
The handwheel will not turn, an actuator stalls on torque, or the stem turns with no change in flow.
Likely causes
Years in one position, corroded stem threads, dried sealant in plug valves, overtightened packing, or a wedge gate closed hot. A stem that turns but changes nothing may mean the gate has come off, which forum engineers link to corrosion, sand, velocity, water hammer and build quality.
What to do
Rock the valve gently in small movements, because cheater bars break stems and gears. Lubricate stem threads, inject sealant on lubricated plug valves, and exercise critical isolation valves on a schedule. When internals fail, take the valve apart to find the cause before reordering, and replace any body weakened by corrosion. A higher pressure class alone does not make the internals sturdier.
Sources
1, 10, 11, 13

Rating valves on Sorque

Every Sorque review scores equipment from 1 (poor) to 10 (great), or N/A, on the same five metrics. For valves, these are the things worth weighing:

Effectiveness
Did the valve do its job: tight shutoff in isolation duty, stable control in throttling duty, or clean reseating for check and relief valves? Compare actual seat leakage and capacity with the datasheet.
Reliability
Consider the time between unplanned interventions (packing leaks, passing, sticking, actuator faults) and whether the valve worked on demand after long idle periods. Note the fluid, temperature and cycle rate.
Maintenance
Consider how easily packing, seats and seals can be adjusted or replaced, whether repairs can be done in line, and the cost and availability of trim and seal kits.
Efficiency
Consider the energy cost of the valve’s pressure drop when open, losses from seat or stem leaks, actuator air or power use, and heat lost from bare valve bodies in hot service.
Downtime/replaceability
Consider how fast the valve can be isolated, repaired or swapped (standard face-to-face dimensions, flanged versus welded ends, lead times) and whether a failure forced a shutdown.

Industrial valve maintenance checklist

Intervals depend on the service: Valve World Americas notes that pressure, temperature, fluid chemistry and cycle count all change wear rates. Before opening or repacking a valve, isolate it, relieve stored pressure and verify isolation under lockout/tagout. OSHA’s 29 CFR 1910.147 lists line valves as energy-isolating devices.

  • Walk down valves on a regular route, looking for stem, bonnet and body-joint leaks and corroded bolting.
  • Adjust packing evenly when weeping starts, and log repeat leakers for repacking or upgrade.
  • Check closed valves for passing with pressure, temperature or ultrasonic checks, especially on flare, drain and bypass lines.
  • Exercise idle isolation valves where the process allows, so they work when needed.
  • Lubricate stem threads and gearboxes, and inject the specified sealant on lubricated plug valves.
  • On control valves, compare controller output with actual stem travel and test fail action at shutdowns.
  • Listen for check valve slam or chatter, and inspect hinge pins, disks and seats at turnarounds.
  • Have pressure relief valves tested and repaired by an authorized organization, such as a National Board VR certificate holder, at the intervals your code, jurisdiction and inspection program require. Never gag, block or adjust one yourself.
  • Refit insulation on hot valves after work. The DOE advises insulating surfaces above 120°F to protect personnel. It estimates that a 1-inch removable pad on a 6-inch, 150-class flanged valve at 400°F saves about 5,800 Btu per hour. Check old insulation for asbestos before removing it.
  • Tag repaired valves with their function and inspection interval.

How to choose an industrial valve

Start with what the valve must do, then narrow the choice by fluid and operating conditions.

Function
Isolation: gate, ball, plug or butterfly. Throttling: globe or control valve, or butterfly for coarse control in large lines. Backflow: check valve. Overpressure: a code-compliant relief device.
Fluid
Slurries favor pinch, diaphragm, plug or knife gate valves. Corrosive fluids need lined, alloy or diaphragm designs. Screen liquid services for cavitation and flashing.
Pressure and temperature
Confirm the body’s pressure-temperature rating (ASME B16.34 covers flanged, threaded and welding-end valves in steel and alloys). Check that soft seats and liners survive the maximum temperature.
Shutoff tightness
Put a seat leakage class or test standard on the datasheet. Safety-critical isolation may need double block and bleed or a blind.
Sizing
Size control valves to the flow, not the pipe. Per Valve Magazine, a correctly sized globe control valve is typically one size below line size, and a ball or high-performance butterfly valve about two sizes below.
Pressure drop and energy
Where pressure loss costs pump or compressor power, prefer full-bore valves and low-loss check valves. WaterWorld suggests comparing check valves by turning their headloss into a yearly energy cost.
Actuation
Choose manual, gear or powered operation, a closing speed that will not cause hydraulic shock in liquid lines, and a fail position that suits the process hazard.
Emissions
In VOC or toxic service, specify low-emission packing and consider bellows-sealed or quarter-turn designs type-tested to API 624, API 641 or ISO 15848-1.

Frequently asked questions

What are the main types of industrial valves?

The main families are gate, globe, ball, butterfly, plug, check, diaphragm and pinch, control, and pressure relief valves. Gate, ball, plug and butterfly valves mostly isolate, globe and control valves regulate flow, check valves stop backflow, and relief valves guard against overpressure.

Can a gate valve be used for throttling?

Not as a regular practice. A partly open gate vibrates, and fast flow near closure wears the disk and seat until the valve stops sealing. Run gate valves fully open or fully closed, and throttle with a globe, butterfly or control valve.

Which valve is best for throttling flow?

Globe valves are the traditional choice, giving fine, stable control at the cost of pressure drop, and automatic control uses a control valve with a positioner. Butterfly valves suit coarse throttling in large lines, while standard ball valves throttle poorly unless they have a V-port or segmented ball.

What is the difference between a gate valve and a ball valve?

A gate valve slides a wedge across the flow with a multi-turn handwheel, while a ball valve turns a bored ball a quarter turn. Ball valves are faster, seal tightly with low torque and are the usual choice for gas isolation. Gate valves close gradually, which limits surges in liquid lines.

What is the difference between a safety valve and a relief valve?

A relief valve opens progressively as pressure rises above its set point and is typical for liquids. A safety valve pops fully open and reseats only after pressure has fallen by its blowdown margin, which suits steam and gas. Only qualified, authorized personnel should set or repair either.

Why do valves leak at the stem?

Most stem leaks come from packing or stem O-rings that lose compression as the stem cycles or wear against a dirty or corroded stem. Evenly tightening the gland nuts often stops a new leak. If it does not, the valve needs repacking, and any scored stem needs repair.

What causes control valve hunting?

Common causes are tight packing, an oversized valve working near its seat, loose linkage, a misconfigured positioner, poor instrument air and aggressive tuning. Small output steps with the controller in manual show whether the valve or the tuning is at fault, and retuning will not cure a sticking valve.

What causes check valve slamming?

Slam happens when the disk is still open as flow reverses and then shuts abruptly, sending a pressure surge through the line. It is most common on pump discharges after a pump trip. Fixes include fast-closing spring-assisted checks, dashpot-damped slow closure, and sizing for the actual flow.

Peer reviews of valves

Rated 1 to 10 by engineers, mechanics, and technicians who have run or maintained them.

Add an equipment review

Ratings1 (poor) - 10 (great), N/A (Not applicable)

How well does it achieve its intended purpose, e.g., measurement accuracy of sensors. Enter 1 (poor) to 10 (great), or N/A.

How likely is it to fail or seize. Enter 1 (poor) to 10 (great), or N/A.

Effort and attention needed to maintain high quality operation. Enter 1 (poor) to 10 (great), or N/A.

Performance/cost - can be energy, economic, or other costs. Enter 1 (poor) to 10 (great), or N/A.

Length of time from breakdown to operation and ease of securing replacements. Enter 1 (poor) to 10 (great), or N/A.

At least 20 characters. Reviews are public; leave out names and confidential details.

Sources

Pages this guide draws on, checked when it was last updated. Links go to other sites.

  1. DOE Fundamentals Handbook: Mechanical Science, Volume 2 of 2 (DOE-HDBK-1018/2-93), Module 4: Valves · U.S. Department of Energy
  2. Leak Detection and Repair: A Best Practices Guide · U.S. Environmental Protection Agency
  3. Install Removable Insulation on Valves and Fittings (Steam Tip Sheet #17) · U.S. Department of Energy, Advanced Manufacturing Office
  4. 29 CFR 1910.147, The control of hazardous energy (lockout/tagout) · U.S. Occupational Safety and Health Administration
  5. Deftly Deal With Control Valve Problems · Chemical Processing
  6. Size Matters: Control Valve Sizing 101 · Valve Magazine
  7. Flashing and Cavitation · Valve Magazine
  8. Understanding and solving control valve cavitation problems · Processing Magazine
  9. Choosing the Right Check Valve · WaterWorld
  10. Valve Maintenance and Troubleshooting · Valve World Americas
  11. Gate And Check Valve Issues · Cheresources.com Community (Industrial Professionals forum)
  12. Type Of Isolation Valve (Ball / Gate) · Cheresources.com Community (Refining, Hydrocarbons, Oil, and Gas forum)
  13. "Frozen" gate valves · Heating Help: The Wall
  14. Best valve stem packing for single pipe steam valve · Heating Help: The Wall
  15. Closed-loop control troubleshooting · ISA InTech
  16. How to know if the tuning or the valve is responsible for oscillations · Control Global
  17. B16.34 - Valves - Flanged, Threaded, and Welding End · ASME
  18. VR Stamp (accreditation of pressure relief valve repair organizations) · The National Board of Boiler and Pressure Vessel Inspectors